MM GA F TA K A AL oD oI F GA oD MM H A AL NA C C TA oE 0 .0.05 H1 H1 R0.4 R0.4 8 x J ZZ + 2 Stroke S + Stroke 2 x RcP H + Stroke Width across flats KA 4 x TC Width across flats B1 Width across flats KB Width across flats B1 oE 0 .0.05 Precautions Be sure to read this before handling. Refer to the back cover for Safety Instructions. For Actuator and Auto Switch Precautions, refer to “Handling Precautions for SMC Products” and the Operation Manual on SMC website, http://www.smcworld.com Handling/Disassembly Basic with Rubber Bumper: CG1KWBN (mm) (mm) Note 1) Dimensions are the same as those for the CG1W standard. Refer to page 29. Bore size Stroke range A AL B1 C D DK E F GA H1 I J K KA KB MM NA P S 20 Up to 1500 18 15.5 13 14 8 9.2 12 2 12 5 26 M4 x 0.7 depth 7 5 6 8 M8 x 1.25 24 1/8 77 25 Up to 1500 22 19.5 17 16.5 10 11 14 2 12 6 31 M5 x 0.8 depth 7.5 5.5 8 10 M10 x 1.25 29 1/8 77 32 Up to 1500 22 19.5 17 20 12 12 18 2 12 6 38 M5 x 0.8 depth 8 5.5 10 10 M10 x 1.25 35.5 1/8 79 40 Up to 1500 30 27 19 26 16 16 25 2 13 8 47 M6 x 1 depth 12 6 14 14 M14 x 1.5 44 1/8 87 50 Up to 1500 35 32 27 32 20 20 30 2 14 11 58 M8 x 1.25 depth 16 7 18 18 M18 x 1.5 55 1/4 102 63 Up to 1500 35 32 27 38 20 20 32 2 14 11 72 M10 x 1.5 depth 16 7 18 18 M18 x 1.5 69 1/4 102 Bore size TA TC H ZZ 20 11 M5 x 0.8 35 147 25 11 M6 x 0.75 40 157 32 11 M8 x 1.0 40 159 40 12 M10 x 1.25 50 187 50 13 M12 x 1.25 58 218 63 13 M14 x 1.5 58 218 * Caution on handling/disassembly is provided in addition to that shown below. Refer to page 10. Caution 1. Avoid using the air cylinder in such a way that rotational torque would be applied to the piston rod. !If rotational torque is applied, the non-rotating guide will become deformed, thus affecting the non-rotating accuracy. Refer to the table below for the approximate values of the allowable range of rotational torque. !To screw a bracket or a nut onto the piston rod, make sure to retract the piston rod entirely, and place a wrench over the flat portion of the rod that protrudes. Tighten it by giving consideration to prevent the tightening torque from being applied to the nonrotating guide. Allowable rotational torque (N・m or less) o20 o25, o32 o40, o50, o63 0.2 0.25 0.44 2. When replacing rod seals, please contact SMC. Air leakage may be happened, depending on the position in which a rod seal is fitted. Thus, please contact SMC when replacing them. 46 Air Cylinder: Non-rotating Rod Type Double Acting, Double Rod Series CG1KW CG1�ｮQ CBG1 CG1KR CG1R CG1KW CG1K CG1 CG1W CG1 Low Friction With End Lock Direct Mount, Non-rotating Rod Direct Mount Non-rotating Rod Standard Double Acting, Single Rod Double Acting, Single Rod Double Acting, Double Rod Double Acting, Single Rod Single Acting, Spring Return/Extend Double Acting, Double Rod Double Acting, Single Rod Made to Order Auto Switch